We present two types of ICF (INHIBIT Controlled by Fluxon) gates as the basic circuits of the phase-mode logic family, and fabricate an adder circuit. The experimental result demonstrates that the carry operation followed up to 99 GHz input pulses. The performance of Josephson devices is improved by the use of junctions with high current density (Jc). We may use the high-Jc junctions without external resistive shunt in the phase-mode logic circuits because of reduction of the junction hysteresis. One of the ways to overcome the large area occupancy for geometric inductance is to utilize the effective inductance of a Josephson junction itself. We investigate a circuit construction with high-Jc inductor junctions, intrinsically overdumped junctions and junction-type resistors for the compactness of circuit integration, and discuss various aspects of the circuit construction.

YBa2Cu3O7-δ co-planar Josephson junctions by Focused Ion Beam were characterized by changing the thickness of YBa2Cu3O7-δ films. The junctions had the thickness dependence of the characteristics. The characteristics were dominantly divided into two types. One had the I-V curve of a flux-flow junction and a weak magnetic response. The other had the I-V curve of RSJ, the IcRn product from 0. 1 mV to 0. 5 mV at 4. 2 K, and a good magnetic response. The critical current density of the junctions increased exponentially with increasing film thickness. From the observation of the junction surface, the junction length was decreased with increasing film thickness by the horizontal growth of the normally grown YBaCuO. In the thicker film (above 240 nm), the microshorts of the normally grown YBaCuO on the abnormally grown YBaCuO area were observed. It is considered that the main part of Josephson current for the junctions changes from the abnormally grown YBaCuO to microshorts when increased with the film thickness.

We have studied the effect of Ga and Ca substitution in the PrBa2Cu3Oδ (PBCO) barrier on the parameters of high-temperature-superconductor ramp-edge Josephson junctions. Pr 1-XCa XBa2Cu3Oδ (X=0. 15, 0. 3) had reduced bulk barrier resistivity as small as 10 mΩcm which was close to the metal-insulator transition. Also, PrBa2Cu 3-ZGa ZOδ, written as GaZ-doped PBCO (Z=0. 15, 0. 3, 0. 6), had enhanced resistivity neater than 1 kΩcm at 4. 2 K. The transport mechanisms in these bulk barriers fitted well with the Mott variable hopping model. The critical current density Jc and normalized junction conductance (R nA)-1 decayed exponentially with almost the same decay length, as the barrier thickness increased. The decay length depended on the barrier material, and ranged from 1. 7 nm to 6. 5 nm for Jc, from 1. 9 nm to 7. 2 nm for (Rn A)-1. Because on these experimental results, we conclude that direct tunneling is the dominant transport mechanism for both quasi particles and paired particles in our junctions, while resonant tunneling should be considered as an additional transport mechanism of these two kinds of particles in the junctions with the PBCO-based barriers reported so far. It was also found that Ga doping raised the characteristic voltage Vc while Ca doping reduced it, though the Vc values obtained here were still small compared to the theoretically predicted values. The spacewise metal insulator transition at the interfaces caused by a high density of localized states in the barriers seemed to be responsible for the reduction in Vc. The best Vc value was 0. 32 mV at 77 K and 5. 2 mV at 4. 2 K using a Ga0. 6-PBCO barrier. These Vc values are suitable for electronics applications. Furthermore, superconducting-gap-like structures were observed in the junctions with highly resistive Ga-doped PBCO barriers.

We describe several properties of very thin stacks of 10 to 20 intrinsic Josephson junctions fabricated on the surface of Bi2Sr2CaCu2O8+δ single crystals. We show that the Joule heating is significantly reduced in these stacks and that the gap structure is clearly observable in the quasiparticle current-voltage (I-V) characteristics. The I-V curves are characterized by a large subgap conductance and a significant gap suppression due to the injection of quasiparticle current. It is found that the IcRn product of these intrinsic Josephson junction stacks is significantly small compared with that expected from the BCS theory. It is also found that there is a tendency that IcRn decreases with increasing c-axis resistivity. Both Ic and the gap voltage exhibit unsaturated temperature dependence at low temperatures. The behavior presents a sharp contrast to that of Josephson junctions made of conventional superconductors. The characteristics are discussed in relation to the d-wave symmetry of the order parameter.

We have studied an in situ edge preparation process and the effect of a substrate rotation during the edge preparation in order to improve the uniformity and electrical characteristics of high-Tc edge-type Josephson junctions. The improved YBa2Cu3Ox/PrBa2Cu3Ox/YBa2Cu3Ox edge junctions showed small 1σ-critical current spreads as low as 10% for 12 junctions. We have confirmed that the spreads do not increase significantly by adding groundplane over the junctions. In this paper, we will describe these processes developed for the fabrication of high-Tc superconducting integrated circuits.

We investigate the basic properties of focused electron beam (FEB)-damaged Josephson junctions on silicon (Si) substrates for high-frequency device applications. YBa2Cu3O7-y (YBCO) Josephson junction arrays were also fabricated by FEB irradiation to confirm the junction uniformity and to investigate their applicability. The junctions exhibit resistively shunted junction (RSJ)-like current-voltage (I-V) curves and the microwave-induced Shapiro steps for all operation temperatures. Two-junction arrays show single-junction-like behavior with the Shapiro steps in an array up to 2 mV. Microwave-induced Shapiro steps correspond to the double voltages Vn=2nVJ, where VJ=f0h/2e in two-junction arrays. The microwave power dependence of I-V curves shows the steps corresponding to the RSJ model.

We report the strong microwave Josephson radiation from an array of high-Tc junctions on a MgO bicrystal substrate from centimeter- to millimeter-wave ranges. The dc bias current was fed to the junction array having parallel geometry with the pair of junctions shunted by superconducting loops. The configuration of bias leads was a series of interlocking dc SQUID's geometry which guaranteed the oscillation of all junctions at the same frequency. For a five-junctions array, we observed the coherent output power of about 13 pW at receiving frequency fREC22GHz without an external magnetic flux, which was nearly five times higher than that of a single bicrystal junction. We observed the Josephson linewidth of the selfradiation in coherent state less than 1 GHz by the adjustment of the external flux. The phase differences between adjacent junctions with different IcRn products could be controlled by an external small magnetic field. Submillimeter-wave detector response of the five-junction array was also studied experimentally at frequency f478 GHz.

Logic operations in principle have been demonstrated based on the planar high-Tc Superconducting QUantum Interference Device (SQUID). Two kinds of logic gates were produced by using the focused ion beam (FIB) superconducting weak links fabricated in NdBa2Cu3O7-δ (NBCO) thin films. Logic gates investigated in this paper are (1) an rf-SQUID based logic gate which utilizes threshold characteristics, and (2) a dc-SQUID based logic gate which is an elementary gate of RSFQ circuits. Elementary logic operation such as (1) AND/OR logic and (2) SET-RESET flip-flop operation were successfully obtained in the logic gates. In addition to the present experimental results, some problems and future prospects are also discussed.

We successfully observed curent-voltage (I-V) curves which showed the behavior of intrinsic Josephson junctions using Tl2Ba2CaCu2Ox (Tl-2212) thin films on MgO substrates by structuring mesas and measuring the electrical transport properties along the c-axis. For a 55 µm2 mesa, a hysteretic I-V curve was observed up to 80 K, which showed that series-connected SIS-type junctions are formed. Compared with the critical current density (Jc) of more than 106 A/cm2 parallel to the ab-plane, an anisotropic Jc of 1.4102 A/cm2 along the c-axis was observed at 4.9 K. By focusing on the I-V curve at lower bias current, the constant voltage jumps measured at the first seven branches were estimated to be 26 mV. The normal resistance (Rnk) of a unit SIS junction was estimated to be 580 Ω by substituting the measured voltage jump in the Ambegaokar and Baratoff relation. Using the calculation for McCumber parameter (βc), the capacitance (Ck) of the unit SIS junction was estimated to be 3.610-10 F/cm2 at 77 K. The IckRnk product was estimated to be 6.4 mV and the cut-off frequency (fc1/2πRnkCk) was calculated to be 3.1 THz at 77 K. The Jc and the hysteresis decreased with an increase in the mesa area, and finally, for a 300300µm2 mesa, a resistively shunted junction (RSI) like curve without hysteresis was observed up to 98 K. A Jc of 5.6101 A/cm2 along the c-axis was observed at 6.4 K. This may be explained by the higher content of conductive grain boundaries for a larger mesa area.

Bifurcation Phenomena observed in a circuit containing two Josephson junctions coupled by a resistor are investigated. This circuit model has a mechanical analogue: Two damped pendula linked by a clutch exchanging kinetic energy of each pendulum. In this paper, firstly we study equilibria of the system. Bifurcations and topological properties of the equilibria are clarified. Secondly we analyze periodic solutions in the system by using suitable Poincare mapping and obtain a bifurcation diagram. There are two types of limit cycles distinguished by whether the motion is in S1R3 or T2R2, since at most two cyclic coordinates are included in the state space. There ia a typical structure of tangent bifurcation for 2-periodic solutions with a cusp point. We found chaotic orbits via the period-doubling cascade, and a long-period stepwise orbit.

A binary counter circuit in the extended phase-mode logic (EPL) family is presented. The EPL family utilizes a single flux quantum as an information bit carrier. Numerical simulations show that a binary counter circuit with a Josephson critical current density of 1 kA/cm2 can operate up to a 30 GHz input signal. The circuit has been fabricated using Nb/AlOx/Nb Josephson junction technology. New interface circuits are employed in the fabricated chip. A low speed test result shows the correct operation of the binary counter.

In this paper, oscillation modes produced in a Josephson circuit and its application to digital systems are described. The analysis is performed using an analog simulator to model the Josephson junction, in addition to computer simulation. The experimental results concerning oscillation modes agree well with the simulation results. The main advantage of the mapping for the oscillation modes is that it allows understanding of the relationships among oscillation modes and circuit parameters at first sight. In addition, a novel application of nonlinear oscillation to digital systems is described.

We have developed a strato-mesospheric ozone monitoring system with a low noise SIS mixer, which receives 110.836 GHz millimeter-wave emission due to the rotational transition of ozone molecules (J=61,560,6). The system is completely standalone. We derived the altitude profile of ozone density between 25 km and 80 km from the observed spectrum. The receiver noise temperature was as low as 17 K (DSB), so that the altitude profile could be obtained every 3-10 minutes. The monitoring system can operate continuously over one year without any maintenance work, because it utilizes a 4 K closed cycle helium refrigerator and reliable Nb/AIOx/Nb SIS junctions. We used two acousto-optical spectrometers (AOSs) as real-time spectrometers because of their high resolution and simple construction. In an up-to-date system, one AOS would have a band-width of 65 MHz and the other, a band-width of 250 MHz with resolutions of 40 kHz and 250 kHz, respectively. A computer controls the entire system and is also used to analyze measured data. In this paper, we present the principles of system operation, the latest performance and the construction of the system, and some observed data.

The high-Tc superconducting active antenna proposed here for millimeter and submillimeter radiowave communications, uses a YBCO slot antenna with a series Josephson junction array to increase the normal-state resistance of the junctions, in order to ensure impedance matching between the antenna and the junctions. The antenna is a coplanar waveguide fed slot antenna, which can be easily and monolithically combined with the Josephson junctions. The design frequency of the antenna is 10 GHz and the obtained bandwidth of a VSWR less than 2 was 4.1%. Normal-state resistance values of the junction array could be confirmed by measuring I-V characteristics and 100-MHz impedance measurements, and both agree very well. Microwave mixing experiments were carried out using the junction array with the antenna, and the experiments showed that the conversion gain of the junction was proportional to the number of the junctions. The conversion gain of an eight-junction mixer with the antenna was found to be -6 dB.

A YBaCuO-Nonsuperconductive YBaCuO-YBaCuO coplanar Josephson junction has been fabricated, using Nonsuperconductive YBaCuO thin film deposited on an MgO(100) substrate with intentional and very local damage which was created by Focused Ion Beam. The YBaCuO grown on the damaged section of the substrate turned out to be non-superconductor, due to implanted Ga ions and the change in the crystal quality, facilitating formation of an S-N-S junction. We found the important fact that the critical current density decreased exponentially with inverse of the junction length which was changed from 0.2 to 1 µm, and that Ga ion was detected in the thin films of the junctions, and that the thin films of the junctions were formed by a mixture of an amorphous, a polycrystal and a crystal, which is confirmed by Transmission Electron Diffraction. And the damaged substrate gave rise to Ga segregation and the mixed crystal, which played an very important role to form the normal metallic YBCO thin film of the Josephson junction. All these facts are related with the S-N-S junctions.

Recenty, the Josephson effect-based voltage standard has been realized by using the Josephson junction array which is constructed by integrating many Josephson junctions. In this article, the 1-V Josephson-junction-array voltage standard used in routine calibration work and further development of the 10-V Josephson junction array at the Electrotechnical Laboratory (ETL) are introduced.

Some qualitative properties of an inductively coupled circuit containing two Josephson junction elements with a dc source are investigated. The system is described by a four–dimensional autonomous differential equation. However, the phase space can be regarded as S1×R3 because the system has a periodicity for the invariant transformation. In this paper, we study the properties of periodic solutions winding around S1 as a bifurcation problem. Firstly, we analyze equilibria in this system. The bifurcation diagram of equilibria and its topological classification are given. Secondly, the bifurcation diagram of the periodic solutions winding around S1 are calculated by using a suitable Poincar mapping, and some properties of periodic solutions are discussed. From these analyses, we clarify that a periodic solution so–called "caterpillar solution" is observed when the two Josephson junction circuits are weakly coupled.

This paper presents a novel and successful logic synthesis method for optimizing ternary logic functions of any given number of input variables. A new optimization algorithm to synthesize and minimize an arbitrary ternary logic function of n-input variables can always lead this function to optimal or very close to optimal solution, where [n (n1)/2]1 searches are necessary to achieve the optimal solution. Therefore, the complexity number of this algorithm has been greatly reduced from O(3n) into O(n2). The advantages of this synthesis and optimization algorithm are: (1) Very easy logic synthesis method. (2) Algorithm complexity is O(n2). (3) Optimal solution can be obtained in very short time. (4) The method can solve the interconnection problems (interconnection delay) of VLSI and ULSI processors, where very fast and parallel operations can be achieved. A transformation method between operational and polynomial domains of ternary logic functions of n-input variables is also discussed. This transformation method is very effective and simple. Design of the circuits of GF(3) operators, addition and multiplication mod-3, have been proposed, where these circuits are composed of Josephson junction devices. The simulation results of these circuits and examples show the following advantages: very good performances, very low power consumption, and ultra high speed switching operation.

We have fabricated Nb/AlOx/Nb Josephson tunnel junctions by a sputtering apparatus with a load-lock system. This sputtering apparatus had the sub chamber for preparation and the main chamber for sputtering. The substrate temperature was confirmed to be kept less than 85 during Nb sputtering at the deposition rate of 1.18 nm/s for 7 minutes. The junctions that had 50µm50 µm area successfully showed the Vm value (the product of the critical current and the subgap resistance at 2 mV) as high as 50 mV at the current density of 100 A/cm2.

Step-edge Josephson junctions (SEJJs), which are made by YBa2Cu3O7 (YBCO) thin films on MgO (100) substrates with gentle step angle (below 40 degrees) have been successfully fabricated. The step-edge, with several angles on the MgO substrate, were made using photolithography and Ar ion beam etching, and then YBCO films were deposited on the step-edges by pulsed laser deposition method. The relationships between step-angles and I-V characteristics, microwave properties and structure of SEJJs were systematically investigated. Shapiro steps were clearly observed only in step-angle range between 10 and 30 degrees. Intermittence and hysteresis on the I-V characteristics were observed above 30 mA without effect from step-angles.